The scope of usage and classification of the charcoal processing machine:

1. This wheel mill(charcoal making machine) is suitable for mixing powder and granular materials, such as refractory mud, clay, fly ash, tailing sand, slag, molding sand, etc. It is widely used in non-burning bricks, autoclaved bricks, refractory materials, ceramics, building materials, and other industries(coal powder making machine).

2. Wheel mills(charcoal making machine) are divided into wet wheel mills (which can handle raw materials with a moisture content of more than 15-16%), dry mills, and semi-dry wheel mills ( when the moisture content of the material is below 10-11%), crushing and mixing wheel mill (the crushing and mixing of materials of different components are carried out at the same time).

3. According to the operation method, the charcoal processing machine is divided into a continuous wheel mill (continuous feeding and unloading) and an intermittent wheel mill (feeding and unloading intermittent feeding).

Row). Wheel mills are divided into iron wheel mills and stone wheel mills according to the material of the wheel. The specifications of the wheel mill are represented by the diameter x width of the wheel(charcoal screening machine).

Main technical parameter of charcoal processing machine:

Working principle of charcoal processing machine:

1. The fixed charcoal production machine is installed on the iron bracket on the bottom-driven rotary wet grinding wheel mill, the bottom of the bracket is connected with a beam, and the middle of the beam is equipped with a vertical shaft and a bearing.

The bevel gear is fixed in the middle of the vertical shaft with a key, and its position is slightly higher than the beam. The motor goes through the reducer. The bevel gear drives the vertical shaft to rotate(coconut charcoal tooth powder making machine).

2. The top of the vertical shaft is equipped with a collar with a crankshaft, and the roller is installed on the crankshaft. The bottom of the grinding disc is inlaid with a sieve plate with holes, and the materials that have been crushed to a certain size can be continuously discharged from the holes(charcoal production machine).

3. Just above the bevel gear, there is a rotary disc with a scraper, and the material falling from the screen hole is scraped into the discharge chute by the scraper in this disc for discharge. There are also 2-3 scrapers with adjustable angles on the roller.

4. The scraper is driven by the vertical shaft to rotate like the roller so that the material on the roller that is pressed by the roller can be re-scraped to the bottom of the roller to continue to smash and feed the material. Effect(charcoal production machine).

5. In addition to the scraper, there are also one or two rakes, which turn the materials compacted by the rollers and discharge the materials that reach the fineness in time, which plays the role of "unloading". In addition, the centrifugal force generated when the roller rotates throws the water and the raw materials to the four walls, and then bounces back, which also acts as a stirring material.

6. Two rollers can be installed at different distances from the center of the vertical shaft to increase the rolling area of the rollers on the roller. To balance centrifugal force, the weights of the two wheels are unequal. The weight is usually adjusted by filling in concrete in the gaps of the closer rollers.

7. The height of the roller on the roller can be adjusted automatically. When it encounters a large block or hard material, the roller can automatically rise, and after passing over the hard object, it will automatically fall due to its own gravity. The roller shaft is connected with the vertical shaft through a crank.

Installation operation of charcoal processing machine:

1. When the charcoal production machine is installed, be sure to make the vertical shaft vertical to the disc. When aligning, the vertical shaft can be hoisted first, the rolling disc is moved, the center hole of the rolling disc is aligned with the vertical shaft, and then the vertical shaft can be vertically dropped into the hole.

2. The two rollers must be of equal weight and of an equal radius of rotation. If the rotation radius of the two rollers is not equal in order to increase the rolling area, the weight of the two rollers should be adjusted to balance the centrifugal force.

3. But it is very troublesome to do so, for the convenience of installation, it is generally not used. A cement fence should be built around the wheel roller, and stone bars are arranged in the wall to prevent the roller from being thrown out and ensure the safe operation charcoal processing machine).

4. After the installation is completed, check the tightening of the screws in all parts, and then you can test the drive. If the operation is normal and there is no abnormal sound, it can be put into production. If there is any abnormal sound, stop and check immediately.

5. When the wheel mill is working, in addition to crushing the material, it is also accompanied by grinding. The wider the roller, the greater the relative slippage and therefore the greater the grinding action. Therefore, when using a wheel mill to pulverize materials of different material properties, the selection of wheel width should be analyzed in detail.

6. The wheel width is generally between 300. If there is a large grinding effect (such as silica) for crushing, the wheel can be selected to be wider; if it is mainly crushed, the wheel width can be selected to be smaller, so as not to consume too much(charcoal production machine).

7. The energy of the stone wheel wears out quickly, and it usually needs to be replaced every two months, and a pair of stone wheels must be replaced at the same time. Before the replacement, prepare the square sleeve in advance, go down to the groove of the new stone wheel, and pour it with cement.

8. Please pay attention to the position of the stone wheel during installation. When the stone wheel is too close to the center of the grinding disc, the water material should not be flushed out, and the discharge is slow, so it is repeatedly rolled and the material is too fine, which is easy to cause suspended materials; if the stone wheel is far from the center of the grinding plate, the water material Straight out, the material particles are coarse and can not meet the crushing requirements.

9. Due to the limitation of the installation height of the equipment, the stone wheel, and the grinding disc cannot be replaced at the same time. Generally, the 300mm-thick disc is thinned to 300-600mm thick and then replaced. During operation, the truck should be started empty, and the material should be fed after the operation is normal; when parking, the feeding equipment should be turned off 15 minutes in advance, and the vehicle should be stopped after the bottom material is unloaded.