The raw material of puff extruder machine:

Corn, rice,millets,wheat,oat,barley etc as ingredients.The effect will be much better if the materials in powder(flour) or grits form.

Moulds and final products of puff extruder machine:

We can make many kinds of shapes of final products, also accept customize. We will send 6 kinds moulds for free with the snack food puffing machine.

Technical information of puff extruder machine:

Introduction of puff extruder machine:

The puffing machine belongs to a kind of equipment for processing puffed food. It uses corn and rice as the main raw materials. The 40 types and 50 types are equipped with 7 sets of templates. By changing the mold, it can process peanut shape, plum shape, biscuit shape, small twist shape, and hemp flower shape. , fried rice-shaped, hollow sticks, and other puffed foods with different flavors, such as processing rice, corn, wheat, etc. in daily life. Its main working principle is to convert mechanical energy into heat energy, and the heat generated when the machine rotates is used to squeeze and cook the food. The obvious feature of puffed food is that the volume becomes larger. The puffed fruit processed by the puffing machine is delicious and crispy, suitable for all ages.

Basic installation operations of puff extruder machine:

1. Preparation: Choose rice or corn free of impurities and stones.

2. Prepare a small stick about 10x10mm square and about 30cm long for spare, and prepare a large vise or strong forceps for spare.

3. Select the shape of the movement abrasive tool you want to make, but the head nut upside down, but the core into the head nut, and then level it with the inner plane of the head nut, and tap it with a tool until it is level with the plane(puff extruder machine).

4. First insert the screw into the main shaft of the machine, and rotate the screw by hａnd so that the screw pin can be inserted into the pin groove of the main shaft, then insert the screw sleeve into the machine and fasten the pin on the screw sleeve to the front barrel. on the pin slot.

5. Tighten the front barrel of the machine head nut, then put on the big wrench, tap the big wrench with a hammer a few times to make it tighten more tightly, and tighten the machine head screw diagonally with the wrench(puff extruder machine).

6. Tighten the head nut and the rear nut of the belt pulley, and the belt should be tightened.

7. When the machine is idling normally, only a small amount of wet rice can be added slowly, that is, a small amount of water is mixed in half or two meters, whichever is just enough to mix the rice), and dry rice or corn is started after the puffed product comes out. . At the beginning of processing, the rice should be added slowly but not broken. After the puffed fruit comes out and forms, the amount of rice input should be gradually increased. If it is found that there is rice turning up at the feeding port, the puff extruder machine is because the machine has not been raised to the normal temperature at the beginning, too much rice is placed, and the outlet is too late to go out, causing the rice to turn back. At this point, stop putting the rice, and put it after the rice that has been turned up is put down. The Puff extruder machine must be processed continuously. After 5 minutes, the temperature will rise.

8. During processing, if it is found that the rice or puffed product at the entrance is turned back and the steam with the smell of burnt smoke emerges, the puff extruder machine is caused by the rapid rise in temperature due to the lack of rice. Use chopsticks or small sticks to remove the Turn back the material and speed up the amount of rice. If the blockage is serious and the material cannot be cut, it can be turned off and removed again, cleaned, and then turned on again.

9. After processing, let the machine idle for 15-30 seconds, wait until the residual rice inside is burnt yellow, turn off the power, remove the machine head nut, screw, screw sleeve, and abrasive tool, and remove the rice until it is clean and ready for use. next time use.

10. The puffed fruit is not hard, not brittle, or has a poor expansion degree. Puff extruder machine is the relationship between rice and moisture. It should be controlled to add a small amount of rice or replace the dry rice.